Sanitary pads are a crucial item in our modern society However, even the staff who produce them do not have a good understanding of the equipment which makes the sanitary pads. If there's a problem with the electrical components of the sanitary pads machine what can the owner do to fix it?

1. Mouth first, then hands

If you have a problem with pull up pants electrical machinery Don't hurry to fix it to fix it. You should first inquire questions about the causes of the fault as well as the causes of the fault. For equipment that is not familiar it is recommended to know the principle of circuits as well as the structural characteristics first. Then, follow the appropriate rules. Before disassembling, be aware of the purpose and position of the component, as well as the connection method and the relationship to other components of every component.

2. External first then internal

First, you should examine the machine for obvious cracks and flaws as well as learn about its history of maintenance and service life span, etc. After that, check on the interior of the device. Before dismantling, all the issues should be sorted out. The device is only dismantled if it is found to be an internal defect. If not, blind disassembly could result in the device being damaged over time.

3. Mechanical first, then electrical

Once you have confirmed that the mechanical components are free of fault Conduct electrical inspections. In the event of determining the fault in the circuit the instrument for detection is the best tool to determine the location of the fault. Once you have confirmed that there is no fault in the contact and that the circuit is operating properly, the relationship between circuits and the machine must be examined in a specific method to avoid misjudging.

4. Static first, then dynamic

If the sanitary pads system is not turned on examine the condition of the equipment's buttons and contactors, thermal relays and fuses to pinpoint the location of the fault. Power-on test, listen for the sound, take measurements as well as evaluate faults and then carry out any maintenance. For instance, if the motor is not in phase, or if the three-phase voltage cannot be assessed then you must take note of the noise and then measure the voltage of each phase separately prior to taking a decision about which phase is damaged.

5. Clean first, then repair

If your equipment is heavily polluted First, clean the switches, wire points and contact points. Then, examine if the controls keys are in bad condition. A lot of failures are due to dust and conductive dust blocks. These are typically removed after cleaning.

6. Power first, then equipment

The percentage of failure in the power supply is responsible for a significant portion of the equipment that is damaged and repairing your power source first will typically yield twice the results in half the time.

7. General first, then special

The failures caused by the poor quality of assembly parts and other equipment failures usually make up approximately 50% of all common failures. The particular faults in the equipment are usually soft faults that must be identified and monitored by expertise and tools.

8. Peripheral first then internal

Do not rush to replace damaged parts first. take into consideration replacing the damaged components after you've confirmed that the circuit in the peripheral equipment is functioning normally. Read more about pull up pants machine, Visit here: www.aladdintop.com

9. DC first, then AC

During maintenance the static operating point for the DC circuit has to be first checked followed by it is the dynamic operational point that will be checked. 

10. Debug after failure

Sanitary pads machines The cost for each pad is expensive. If there's a problem in the electric equipment it needs to be repaired strictly in accordance with guidelines to prevent the expansion of damage and financial damage.

It's beneficial for companies to extend the use of diapers with mechanicals in summer, and to reduce cost of maintenance in case the temperature is abnormal. This article offers the below maintenance tips for issues that easily occur in the equipment for diapers during summer.

1.The adult diaper machine can be at risk of failure during summer.

In high temperatures pipeline explosions joint leakage the solenoid valve coil is burning, blockage of hydraulic valves and noise faults are common in the hydraulic system. The aging circuits during summer are more likely to result in cracks and short circuit faults. When temperatures are high the electrical components of the cabinet for control are susceptible to failure, and crucial control elements like the industrial controllers can also be affected by fatality, slow operation speed, control malfunction and other issues.

2. Adult diapers require maintenance procedures for their machine during the summer months

Boiling is among the most common problems caused by the high temperature of mechanical equipment for diapers. When the temperature of the water is excessively high, don't hurry to open the cover of the water radiator to dissipate heat. It is simple to apply hot water. Mix water in after natural cooling. Depending on the operational experience and technical specifications of diapers' mechanical operation the user must stop the operation as soon as possible and not shut down the engine. Instead, turn off the engine, then open the shutter and increase airflow, then gradually decrease the temperature of the water and release a significant amount of bubbles that are created from the cooling device.

If the engine is idle for a short period of time then the temperature of the water drops and it ceases to boil. The cap on the water heater should be wrapped by a towel or a veil. Make sure to carefully open the cap on the water heater to let the water evaporate out and make sure there is no water vapour from the radiator has been released. Open the water heater cap and then open the cap of the water heater. Be sure that your arms aren't exposed in order to prevent facial water and stop the hot water from burning your face.

3. The most important aspects of the daily maintenance of the adult diaper machine during the summer months

If you are working in areas with high temperatures make sure you raise the oil's viscosity. Also, make sure the cooling system as well as the fuel system are not blocked, change old plugs, wires and hoses, as well as make sure that the fuel pipes are tightened to stop fuel leakage. Clean the dust and oil around the engines to make sure that the engine runs light and provides adequate heat dissipation.

Lubrication of equipment is among the primary methods used to protect parts from wearing out and causing failure. Lubrication plays a significant function in the maintenance and transmission of equipment. It can influence the performance of the equipment, its accuracy, and its service life. In order to lubricate 5 or 3 levels of filtration must be performed according to stipulated lubrication duration the lubrication implementer, the parts for lubrication, lubricating oil amount, storage filtration distribution filtration, and refueling filtration inspection. Reduce friction and damage to guarantee regular operation. More info about adult diaper machine Manufacturers, Visit our website: www.fjhaina.com

Conclusion: Summer maintenance of the adult diaper machines should be based on the guidelines of timeliness, rationality , and completeness. This is beneficial to the functioning of the machine and allows it to adapt to external temperatures and working conditions. Manage the process, learn the dynamics of its performance and develop specific and universal maintenance programs. The equipment needs to be examined and maintained frequently to avoid breakdown, ensure reliability and increase efficiency and effectiveness. Make sure to maintain it regularly as per the conditions of operation and operating guidelines.

The material includes monitoring the operating condition, refilling or changing the lubricant, as well as periodic inspection and disassembly. Maintenance items during operation include bearing rotation sound, vibration, temperature, state, etc.