Are you one of the users struggling for HP Tango printer setup for the first time? Fret not, we got your back with this article. In this article, we will cover end-to-end setup installation steps and guidelines in a user-friendly manner for you to follow easily. Ready to learn more, read along with us.

General instruction before starting with the HP Tango printer setup process:

• Once you got the printer box, carefully unbox it
• Take the printer and keep it in an even surface
• Remove the power cord and other paper that came along the printer box secured for future use
• Keep in mind to recycle the packaging materials
• Check the scanner glass, paper tray, and ink cartridges for unwanted papers and remove them
• Now open the input tray and adjust the paper width guide
• Then take a fresh stack of paper and insert them
• Now adjust the paper width guide to make them in position
• Next thing is to open the ink cartridge access door
• You must wait until the carriage moves and remains idle in a position

Once it becomes silent, take your ink cartridges out from the package and insert them into the printer. Make sure you are not touching any copper contact while inserting them since it may cause permanent damage to those cartridges. Push the cartridges into the slot until it gets lock into its position. Keep in mind to put the respective color in its slot. Then wait for the printer to print an alignment page.

Prepare for the wireless connection setup with your Hp tango printer:

• Initially make sure that your printer and the computer/mobile device is connected to the same local network.
• Make sure that the internet connection is seamless
• Then check that your computer and router are active and not in an idle state
• Your printer must be set with adequate ink and paper loaded into it
• Make sure to place your computer or any device close to the router and not farer than 6 feet

Hp tango printer network connection setup:

There are number of methods available for the HP Tango to establish a wireless connection with your device. We will explain some of the few that could help you with your situation.

Option 1: Establish a wireless connection with Wi-Fi Direct

When you don’t have local Wi-Fi network available, you can opt for Wi-Fi Direct.

• Initially you have to get the Wi-Fi Direct printer name,
  • For printer with control panel, tap on the  Wi-Fi Direct icon
  • This will help you view the Wi-Fi Direct name and password
  • Then from the Reports, choose to print a Network Summary or Network Configuration page
  • Note down the name and password from the Wi-Fi Direct session
• For printer with buttons, press and hold the information button
  • Then hold the Wi-Fi Direct button for few seconds
  • Next press and hold the Information along with the Wi-Fi Direct button
  • Press and hold the resume button of the printer that will print the required report
• Now from the windows search for Printers and Scanners option
• Then tap on the Add a printer or scanner option
• Now chooseShow Wi-Fi Direct printers
• Then choose the printer name that start with Direct in front of its name
• Next tap on the Add Device option and note down the PIN that displayed on the printer control panel
• Then you must enter the PIN within 90 seconds followed by clicking the Next button
• Now choose your printer name with Direct in front of its name
• Once done, choose a document to print, click file and choose print

Option 2: Establish a wireless connection with HP Smart app on windows

• Initially turn on your printer
• Then from your computer, navigate to the HP official site and download the HP Smart app in your system
• From your printer, tap on the wireless button for few seconds and you can see the flashing blue light from the printer
• Then from your computer, open the HP Smart app and click on the plus sign
• From the list of available devices, choose your printer name and click continue
• In the following prompt, enter the Wi-Fi password and click continue
• Once the connection has established, click continue
• Simply follow the online instruction displayed on the screen to complete the connection establishment process
• You can confirm the Wi-Fi establishment between your system and the network with the conversion of solid blue light from the blinking one

Option 3: Establish a wireless connection with HP Smart app on Android

• Initially from your Android device, turn on your Bluetooth feature
• Then from the playstore or eth HP official site, download and install the HP Smart app
• Now from your printer press and hold the wireless button for few seconds
• Then navigate to your Android device and open the HP Smart app
• Now click the plus sign on the app and tap on the Add printer option
• From the list of available printer name, chose your printer name along with the model number
• In the following screen, you will be prompted to enter the WEP or WPA key which is the network password
• Once the printer has established the connection with the printer and the system, follow the instruction to complete the setup process
• You can confirm the Wi-Fi establishment between your system and the network with the conversion of solid blue light from the blinking one.

Read more:

• 
  
  • how to change ink in hp tango printer
  • how to print self-test pages on hp tango printers
  • how to load paper, envelopes, cards on hp tango printers
  • this printer isn't available right now
  • how to fix HP rundll error on startup
  • solve common hp printer problems

Do you need to setup your printer in the wireless mode? Or make your printer accessible over HP Smart app, HP Software or the entire printer setup? You will need to reset hp printer wifi. Besides the restoring the Wi-Fi setup mode also assists with troubleshooting the wireless-related connectivity issues.

In this blog we will curate the end-to-end instruction on resetting the Wi-Fi Setup Mode on HP Printers. Read along to know more with us.

Solution 1: Restoring Wi-Fi setup mode on printers with touchscreen display

• Initially, navigate to your printer control panel
• Then tap on the setup menu
• If the setup icon not available, click on the wireless icon
• Now choose Network setup option
• In the following select Restore Network Settings option
• Next click yes on the access prompt that will be displayed on the control panel

You have to wait for a minute or two to see the wireless light to turn into blue color. Keep that in mind, once your printer has entered into the default mode, you should finish the setup process with two hours or else you have to re-perform restoring the Wi-Fi setup mode process.

Solution 2: Restoring Wi-Fi setup mode on printers without a touchscreen display for HP ink tank and ink jet display

• Initially, navigate to your printer control panel
• Then press on the cancel button to wake your printer and keep it on ready mode
• Now press and hold the wireless and cancel button for some time
• That is until you see a flash from your power button
• Now, wait for a minute or two to see the wireless light to turn into blue color

Always keep in mind, once your printer has entered into the default mode, you should finish the setup process with two hours or else you have to re-perform restoring the Wi-Fi setup mode process.

Solution 3: Restoring Wi-Fi setup mode on printers without a touchscreen display

• Initially, navigate to your printer control panel
• Then press on the cancel button to wake your printer and keep it on ready mode
• Now press and hold the wireless and cancel button for some time
• That is until you see a flash from your power button
• Now, wait for a minute or two to see the wireless light to turn into blue color

Always keep in mind, once your printer has entered into the default mode, you should finish the setup process with two hours or else you have to re-perform restoring the Wi-Fi setup mode process.

Restore Wi-Fi Setup Mode on some of the special HP printers

For HP Laser Neverstop Printers

• Initially, navigate to your printer control panel
• Then press on the cancel button to wake your printer and keep it on ready mode
• Now press and hold the wireless button for some time
• That is until you see that your printer restart
• Now, wait for a minute or two
• That is until you see the wireless light turning blue

Make sure to finish the setup within 2 hours in your HP Laser Neverstop printers or else you have to perform the restoration process.

For HP Laser and Color Laser Series Printers

• Initially, navigate to your printer control panel
• Then press on the menu button
• Now press on the right navigation button from the printer control panel
• This will navigate to the network settings
• Next press ok
• In the following screen, choose Wi-Fi Default
• Then click ok
• Now, wait for a minute or two

Make sure to finish the setup within 2 hours or else you have to perform the restoration process.

For LaserJet M109-M112 Printers

• Initially, navigate to your printer control panel
• Then press on the resume or the cancel button to wake your printer and keep it on ready mode
• If it is not ready you can find it by the ready light is on but is dim
• Now press and hold the wireless button for 20 seconds
• That is until you see the attention light starts to blink on your printer control panel
• Now, slowly release the wireless button

You can see the printer getting restart with the wireless light blinks in the printer control panel. Make sure to finish the setup within 2 hours in your LaserJet M109-M112 printer  or else you have to perform the restoration process.

For HP Deskjet 27 Series Printers

• Initially, navigate to your printer control panel
• Then press on the cancel to wake your printer and keep it on ready mode
• Now press and hold the wireless button and cancel button for some time
• That is like 5 seconds until you see the power lights blinks
• Now, wait for the blue light that is the wireless light to turn blue and to blink continuously

Make sure to finish the setup within 2 hours or else you have to perform the restoration process.

For Envy Series Printers

• Initially, navigate to your printer control panel
• Then press on the cancel or the resume button to wake your printer and keep it on ready mode
• Now press and hold the wireless button for some time
• That is until you see the power and attention lights blink
• Now, wait for a minute or two

Make sure to finish the setup in the HP envy printer within 2 hours or else you have to perform the restoration process.

Read more:

• how to connect hp printer to wifi
• secure hp wireless printer
• how to print hp network configuration page
• hp printer firmware update
• how to find hp printer wifi password

Looking for instructions for Brother printer wireless setup with your wifi network? Then read along for end-to-end assistance with this article.

General instruction for Brother wireless setup

Before starting with the Brother Printer wireless setup, you have to collect and made some prior arrangements for a seamless wireless connection setup. First, make a note of the network name (SSID). Then the network key (password). Find them on the side description of the access point or the router. If you can’t find it there, check the documentation that came along with the router.

• Initially take your power cord and connect it with the wall socket and Brother Printer
• Now turn on your printer
• Then press the menu button from the printer control panel
• Use the navigation button to choose the Network option and click ok
• In the following page use the navigation button to choose the WLAN option and click ok
• Again use the navigation button to choose the Setup Wizard  option and click ok
• In the upcoming WLAN Enable? The message, choose Yes

This will enable the wireless network and start the wireless setup wizard. Now you can see that your Brother printer begins to search for networks and lists the available network. Choose your network and press ok. If the process is complete you can get a connected message. If not the machine will print a wireless connection report. Check the error code and troubleshoot the issue.

Quick steps for Brother device wireless setup with WPS method

For WPS (Wi-Fi Protected Setup), you have to make sure that your Wi-Fi access point/router contains a WPS symbol indicating that it supports the WPS method. Then know the Wi-Fi access point/router Wi-Fi signal range and place your printer within the range.

• Initially press the WPS button on the Wi-Fi access point/router
• Then press and hold the Wi-Fi button on the printer for about 5 seconds
• You can see the blinking Wi-Fi indicator with blue light turning into steady blue light

This indicates the establishment of wireless access between the printer and the devices (computer/mobile) connected to the same network.

Read more:

Brother printer offline windows 10

Connect brother printer to wifi

Brother printer drivers

Brother printer printing issues

The first-time setup- installation for HP Officejet Pro 9015 series printers is covered here. This document applies to the HP Officejet Pro 9010, 9015, 9018, 9020, and 9025 all-in-one printer family.

Step-1 Remove the packaging materials from your printer and unbox it.

To begin, open the printer's box. Then take out the user guide and the ink cartridges that come with it. Remove the printer device from the packaging box now. Next, Remove the foam from both sides of the printer and set aside the power wire. Now take the printer out of the plastic bag. Remove all of the taps from the front of the printer as well as the control panel window. Now Close the scanner lid after removing the foam-based layer by lifting the cover.

Step-2 Make the necessary cable connections and preferences.

To begin, connect one end of the power line to the printer's back and the other end to a wall outlet. Your printer will now start (turn ON) on its own. Then, from the printer control panel, pick your desired language and confirm. After that, you must choose your nation and then confirm your selection.

Step-3 Ink cartridges are installed.

To begin, open your printer's front door and lift the cartridge access door. Remove the plastic insert when the carriage is idle or quiet. Now remove the cartridges from the packaging and unroll them. Next, pull the tab from the plastic tab on the black cartridge to reveal the vent slot. Hold the cartridge by its sides and twist the cap to remove it; you may need to use a lot of force. To avoid clogs, ink failure, and improper electrical connections, do not touch the ink port or metal contacts. Match the letter and colour of the cartridge to the carriage's matching slot. After that, slip the cartridge into the slot while holding it by its sides.

Step-4 Place a stack of papers in the input tray.

The primary paper tray must first be slid out. Remove the cardboard constraint and tape after that. Place the paper guidelines at the top of the stack. After then, fill the stack with regular A4 paper. Make sure the paper stack is pushed all the way into the tray. Now adjust the paper guides so that they are in contact with the stack of papers. If a notice appears on the control panel screen, slide in the paper tray and then tap OK.

Step-5 An alignment page should be printed and scanned.

Firstly, remove the output tray by sliding it out. An alignment page will now print on its own. Before you start printing papers, make sure you scan the alignment page. So, open the scanner lid and set the paper on the scanner glass, print side down. For optimal positioning, please refer to the scan instructions. Now close the scanner lid and then press the Scan button. When the message "Alignment Successful" shows on the screen, press OK to finish the hardware setup or installation.

Read More:

Installation of HP Officejet Pro 8710-8720 series first-time printer setup

HP Officejet Pro 8600, 8610 series installation first-time printer setup

Installation of HP Officejet Pro 8020-8030 series first-time printer setup

HP Officejet Pro 6968-6978 series installation first-time printer setup

Through this blog, you will learn how to connect your printer to wifi with the help of the HP smart app.

Note: Almost all the wireless printers manufactured in the year 2010 and later are compatible with HP smart app.

Download, install and run the HP Smart app

• Firstly download the HP Smart app for Windows or Mac platform from their respective online store.
• You need to create a new HP account to reach all printer services if using it first time on your device.
• Otherwise, you can sign in with your HP login details.
• Make sure your Mac or Windows 10 based computer or laptop and Android, iOS, iPadOS based smartphone, or tablet connect to your local wifi network.
• Ensure the strong strength of network signals for the setup process.
• You need to place the printer near the Wi-Fi router during the setup process.
• Now turn ON your HP printer.
• Next, you need to open the HP Smart app and click on the plus (+) sign to add your printer to wifi.
• Now click on the HP printer setup button on the HP smart app.
• Next, it will ask you to enter the Wi-Fi password of your router that is the WEP or WPA key.
• Now HP smart app will begin the connection process between the printer and the local wifi network.
• Next, you are suggested to follow the on-screen instructions to complete the setup process.
• Finally, click on the exit button when your hp printer is connected to the wifi.

Read more troubleshooting guides for:

hp printer failure

hp printer paper jam

incompatible cartridge hp printer

hp printer not printing black